All posts by sweetchil

Guide to cutting down trees

1. Chainsaw and cutting: Being Predictable

When cutting trees with a chainsaw, preparation is essential. If you are planning a tree felling and forestry equipment, you are not only ready for a safer work session, but it will be greatly simplified to work after a tree is felled. First, ask yourself if the area presents significant obstacles, such as airlines, roads or buildings. Deploy warning signs if you know that a road crosses the forest area or that many people pass through it on a daily basis.

2. Cutting the tree: check the direction of the fall

Continue by determining the direction of the fall through careful examination of the tree. What do the branches look like and how do they grow? Also, consider the direction of the wind. If you are unsure of the natural direction of the tree’s fall, move away from the tree and check with a plumb line. Clear the area around the tree in the intended direction of the fall. Also clear the space at 45 degrees behind the tree in both directions, to give you a way to retreat.

3. Prune the trunk

When you have cleared the area, installed your warning signs and decided on the direction of the fall of the tree and your way of retreat, you must verify that you have enough fuel in the tank for the task to be accomplished. Then you have to prune the trunk to eliminate all the branches and branches that could hinder you when cutting the slash. The safest way to prune is to work with a traction chain (under the guide bar) from top to bottom. Learn how to safely and efficiently unplug a tree.

4. Choose cutting technique

When the trunk no longer has branches up to shoulder height, the stroke should be carried out. In this operation, two things must be remembered: the hinge must have a uniform thickness with the correct dimensions and the corner or the felling lever must be inserted before the shaft can pinch the bar. The technique to be used for cutting depends on the size of the tree and the slope, as well as the size of the chainsaw used for the cut. We have gathered here information about the different techniques, so that you can find the method most suited to your conditions.

5. Tools: Chainsaws and Table Saws

There are several cutting tools among which make your choice to cut down the tree. The size of the tree determines the type of forestry equipment required. For smaller trees, you normally do not need felling tools. Physical strength is enough, possibly helping you with a long boom. The cutting corner provides a greater force than the different types of levers. In extreme cases, you can use a rope and a winch, which is the safest and most powerful method for felling a tree. For bigger trees, on the other hand, you will not only need a chainsaw but also one of the best table saws once it’s cut down. A table saw will help to further cut down the chunks into the sections needed to be used.

What features to look for in a garbage disposal?

Rugged

InSinkErator disposals are designed and manufactured to the highest standards, are all equipped with overheating stoppage; they do not require maintenance; the parts have a guarantee of 3-7 years depending on the model; solid and light construction, including stainless steel, are the guarantee of outstanding performance and durability.

Easy to put together

the exclusive quick-lock setup system makes it easy to connect to the sink; each disposal comes with a fixing system for a standard sink of normal thickness (max. 30mm) with a 100mm diameter diameters. For special sinks (with a 50 mm diameter, thicker diameter), connection accessories are always available.

Good operating

The induction motor of the disposal, equipped with permanently lubricated bearings, has been made exclusively for the needs of the consumer; it has high torque that ensures quiet operation and sustained efficiency no matter what the load; all disposals are equipped with a spacious grinding chamber allowing the rapid and easy introduction of large volumes of food waste; the rotating fully, the stainless steel feeder improves the grinding result and gives maximum protection against the risk of damage, with the presence of an automatic reversal for certain models, which ensures uniform wear of the crushing blade and a long service life of the device.

Available in a wide range of models

InSinkErator offers a range of many domestic models, each equipped with different options; Several start-up devices are available (conventional wall switch, pneumatic style, controlled radio switch preventing the worktop from being drilled, magnetic plugs. You can see the top disposal reviews here from the Insinkerator brand if you are interested.

Compact

The grinding chamber and the motor have an optimal shape and design to allow enough space under the sink so that you don’t have to worry about it taking up to much space.

Cleaning the sink: What you need to know

cleaning the sinkAnyone who is accustomed to spending some time in the kitchen, will know then that cleaning the sink can be a hard task. After all, this is the last place where many of the food remains of those delicious dishes that we clean after eating, in addition to all the drinks, and germs that this entails.

Often, no matter how carefully you do, those stains on the remains seem to want to stay there forever and it is difficult to remove them.

Well, that was until now. There may be very corrosive chemicals to help clean it, but today we bring you a very effective home trick and you only need two ingredients that you have at home:

You simply have to look for baking soda and follow the next steps. In a few minutes, you will have a sink so clean that you will feel like eating it (well, that’s not recommended).

The answer is to use a widely known substance called baking soda! Yes folks, that is all you need I’m telling you. You can use it everywhere in the sink.

What about the faucet you ask? Well for the faucet you can also use baking soda and a damp rag too. If you’re in the market for a new one then check out some kitchen faucet examples if you need to.

Well, that’s all we have for this article.  If you are happy with it then drop me a line and we can have a chat.

Sweet Chilis

Sweet Chillis are a kind of spicy chili that is found in a few places around the world. That’s where the name for this site was inspired, as it is a sweet place to read posts about a variety of topics.